Find the user manual and the help you need for the products you own at ManualsOnline. I got an old laptop model MA2 without powersupply. SetIP command to see and change the IP addresses of the console. This command can be used to change both Ethernet connectors and even set a gateway. Requirement: STP (shielded twisted pair) cable with RJ45 connector, min. Cat 5e . To connect Ethernet port 1: Connect one end of an Ethernet cable to the.

Author: Meztim Arakus
Country: Mongolia
Language: English (Spanish)
Genre: Science
Published (Last): 13 April 2016
Pages: 88
PDF File Size: 5.73 Mb
ePub File Size: 11.89 Mb
ISBN: 907-8-94595-345-7
Downloads: 1031
Price: Free* [*Free Regsitration Required]
Uploader: Taujind

Not the chip, that is USB driver. Then type the new IP address – and reboot. Don’t have a good battery to test with and the customer isn’t that gatewaj in buying a new one for a laptop that may have a mainboard issue. It powered right up!

I can’t seem to figure out what is wrong with this gateway ma2

Upon further review, it appears that if I jump the post to the left leg of the marked diode, It registers the battery as charging and is able to power on. I tried it first on a salvage DV board set up in a similar way and it burned up some fets. I’ll attempt to re-create the same test here. Open topic as PDF. Any help or information would be greatly appreciated I traded for a MA3 MX Took it apart today.


What can i test? I went to a technician and he kept saying if i want i could trade it in and buy a dell he has at a cost. The motherboard is slightly manula than the MA7 you describe here. The Laptop is totally dead, the battery does not take manuxl, I charged the battery with other laptop and nothing, the laptop dont start. StormJumperJul 22, Operating perfect for 1 hour.

I haven’t checked the mosfet, but i’m not sure were that is. I except the stupid award for the month!! I have a gateway MA2 with a similar board. I currently have run into a ma3 that is slightly different then the ma7. Sam Mon Mar 28, This LED only lights up when your notebook is connected to AC power or the battery charge is very low.

After getting the same problem with a different motherboard, knowing it was a grounding issue. Good job – I am getting power all the way up to that point already though. We are all learning, and have to sometimes experiment, finding a solution is often rewarding and satisfying.

Hoosier, It will be sometime till I can test the battery ,a2.

Will verify the model number when returning to shop. Mach1 your problem is most likely a shorted cap in the power section.

Ken Mon Aug 16, The outlet working fine good ground, checked the power supply getting DC, ok lets check the continuity. Gateaay shorted, it will read near zero in both directions. If you are unfamiliar with the components, you may need to contact a technician. Meaker Sager Nov 22, I went straight from the pin to the left post of that diode. A drop of flux will help the heat transfer and a drop of solder with a fine tip 40w iron.

  EN 15288-1 PDF Support

Mayo Hardware Sun Jul 25, The chip that the words are on, is the chip to be jumped to. Now it won’t even do that so the customer brought it in.

Still nothing Noot seeing the post above could u email me at nfamar gmail. Mayo Hardware Sun Jan 02, So with the DC Power connected, see if there is power on the back of the jack, Or on the two mznual of the diode shown in the second picture. Any thought on this Help! It’s always the simple stuff we overlook. I have a MA3 with a similar problem. Hay mayo, Holy cow am I so stupid! Are there any side effects to this fix?

Gateway Laptop MA2 User’s manual |

Ok I read the manual and Maanual only get 4 flashing red lights after hitting the power button. The Art-Net addresses have two ranges that are allowed – one starting with 2 and one starting with Windows OS and Software.

You may want to view the latest help version.